Welcome


Greetings!

Thanks for visiting my vintage Hamilton watch blog. I like to restore US-made Hamilton wrist watches back to their original glory and share my experiences with other enthusiasts. Use the "Search" space below if you know what model you're looking for. Feel free to leave polite comments or questions in the spaces provided. Also check out my "watches for sale" on my Etsy site - the link is on the right, just below.

Thursday, January 30, 2014

1954 Standwick

If you've got an eye for detail, you might have realized that there are very few square mechanical models with sweep second hands.  I think the vast majority of non-round models have sub second hands at the 6:00 position.  I've seen a couple of square automatics but there are very few non-round mechanical models with a central sweep second hand.

In fact, the first one I've seen in person is the 1954 Standwick.  It was made for three years.  There were a couple of other similar models in this time frame - but not more than a small handful.

 photo ScreenShot2014-01-30at80301PM_zps73f53178.png

The Standwick comes in a 10K yellow gold filled case with a two-tone sterling silver dial with solid 18K numerals and square markers.  The case curves inward on all four sides like it's been shrunk in the middle.  It was only available with a bracelet.

Under the dial is an 8/0 sized 18 jewel 748 or it's replacement, the 735, depending upon the year.

I recently purchased a Standwick project watch and and boy was it dirty.  It had a layer of grime on every exterior surface.

 photo Standwick01_zpsae275337.jpg

The dial was extremely dirty.  It was so dirty that I thought about leaving it as is because cleaning it might require me to get it refinished… you never can tell how a watch dial will clean up.  I think the grime on this one might be nicotine-related - but that's just a guess.

 photo Standwick02_zps486fcbc2.jpg

The 748 is built on the same platform as the 747 with the sub second.  They share a lot of the same parts.  Once you master taking apart a 747 and think you know what you're doing, you might be tempted to take the 748 apart.

Don't be surprised if it kicks your butt.  My heart still shudders a little when I take a screwdriver to the two screws that hold the four-wheel train bridge on.  These four wheels have very long arbors (shafts) and they can be a real bugger to get lined up again if you're new to the craft.  I'm talking beads of sweat on the forehead, cursing like a sailor, "I swear I'll never take apart another watch"- sort of pain to get back together.  Breaking one of the pivots is the most likely result for the first couple attempts at doing a 748.

 photo Standwick03_zpsf442be4e.jpg

While everything was ultrasonically bathing in cleaner and rinse, I turned my attention to the crystal.  My new glass crystal is curved inward on all four sides, just like the case.  I crossed my fingers that it would go right into place, but as luck would have it, I had to shape it a little with 600 grit wet sand paper.  It took a while but I got it eventually.

 photo Standwick06_zps653d24ab.jpg

Everything is cleaned, oiled, and reassembled.  Next, the finished movement goes onto the timer.  A little tweaking to the regulator brings it in line nicely.  It looks like the two lines are separated by a lot but the bottom line is actually on the top of the screen so they're much closer than it appears.  The beat error isn't as low as it could be but it's not horrible either.

 photo Standwick07_zps9600efc1.jpg

I was able to clean the dial up really well.  I went as far as I could without risking the dial finish and losing the printing.  I think it turned out awesome, if I do say so myself.  With a new crystal and new strap, this Standwick is ready for another 60 years of wrist time

 photo Standwick08_zps1311da05.jpg

Monday, January 27, 2014

1956 Automatic K-404

Did you ever wonder how many Hamilton models there are?  I did too - as I wondered how long I can keep this blog going by showcasing unique models.  Turns out there are over 1,000 so I'm about 25% of the way there.  Of course, many of them I can't afford to buy and quite a few I will probably never even see for sale - like the Barbizon.  But I still have a ways to go nonetheless.

So here's another one to add to the "been there, done that" list.  It's a 1956 Automatic K-404.  It was only produced for one year.

 photo ScreenShot2014-01-26at24848PM_zps43cca084.png

The K-404 comes in a 10K gold filled case.  The sterling silver dial features solid 18K gold numerals and markers.  The dauphine hands are luminous and there are luminous dots at the hour markers too.

It's interesting to note the Hamilton catalog doesn't show that there's a 6 on the dial.  In reality the K-404 has numbers at the 12, 3, 6 and 9 positions.  I think this is the first error I've seen in the artistic renditions of the catalogs.

Behind the dial you will find a 17 jewel Hamilton 661 movement.  This Swiss-made automatic was a workhorse for Hamilton and the dominant movement in automatic models from the 1950's.

I recently purchased a K-404 off eBay.  The listing pictures were terrible and it ended up being a lot rougher than I was expecting.  I didn't pay that much for it but I still probably overpaid based on the condition of the case… as you'll see below.

 photo Vardon13_zpsfdf876aa.jpg

Apparently some moron damaged the case, most likely to test the gold content.  I hate when jewelers damage a piece to sample the gold.

 photo Vardon14_zps389e80a5.jpg

The inside of the case back clearly states the gold content (the outside says it too).  The inside also tells you what model this is.  That seems to occur about 50% of the time.  In other words, sometimes the model name is in the case back and sometimes it isn't.

 photo Vardon15_zps0ccc426f.jpg

The acrylic crystal is very beat up and accounts for most of the watch's rough aesthetic appearance.  Just changing that will make a big difference.

 photo Vardon16_zps51e5581b.jpg

After an overhaul of the movement, you can see below that this 661 is running great.

 photo Vardon17_zpseb91a320.jpg

And here's the finished product, all polished up with a new crystal and nice strap.  I think I'll take the case to my local jeweler and see if they can fix the damage on the sides.  Hopefully that won't be too difficult because otherwise this watch looks great.

 photo Vardon18_zpsbd5cc1a2.jpg

You can see above that the dial is showing a slight case of radium burn from the radium on the hands.  Since they no longer glow I removed the radium in my ultrasonic and then re-lumed the dial and hands with modern, non-radioactive, lume.

 photo dce009a4-1e46-4412-867f-bca5820759c8_zps27be4cfc.jpg

I think this K-404 turned out really well.  Originally I thought I might have to scrap it so I'm glad it could be saved.

Sunday, January 26, 2014

1950 Vardon CLD

Hamilton's foray into waterproof designs was initially more along the lines of "environmentally protected".  That's why they introduced the CLD line.  All of the CLD watches were "sealed against moisture and dirt" but they weren't technically waterproof, per se.

The first CLD watches were introduced in 1948 and additional models joined the line up in 1950.  Among the newcomers was the 1950 Vardon.  The Vardon was produced through 1953.

 photo ScreenShot2014-01-26at25019PM_zps54ee19cc.png

The Vardon came in a stainless steel case with hidden lugs.  There's a gasket between he bezel and the case back and also a gasket in the crown - thus providing the "seal" that other dress watches lacked.

It featured a choice of an applied gold marker / numeral dial or a luminous dial.  The AGN dial's figures were rhodium plated to be silver colored and match the stainless steel.  Like gold, rhodium is a precious metal but it's even more expensive.

Behind the dial you will find Hamilton's 17 jewel 8/0 sized 747 movement.

The Vardon came with either a leather strap or a stainless steel bracelet - the latter being a new option for Hamilton watches.  Many models thereafter would be paired with unique bracelets specially selected to complement each watch's design.

I recently received a Vardon that needed some TLC.  Although it ran, it could be wound continuously and never reached a "fully wound" point.  Manual winding watches have a mainspring that is connected on both ends of the coil - so once it's fully wound it gets tight and stops winding.  When you see a watch for sale that says it's "Over wound" what that really means is "it's fully wound and doesn't run".

Anyway, other than having a mainspring issue, it was in very nice looking, original shape.  The dial has a couple of minor burns from the radium on the hands - but otherwise this watch is close to "new".

 photo Vardon01_zpsbf13dce0.jpg

With the bezel removed, you can see that the movement comes out the front.  The stem is a two-piece design with the female portion retained in the crown.  To get the movement out you need to rotate the stem so you can see the male / female joint.  Then it will lift right out.

 photo Vardon04_zpsdcf1cc05.jpg

The 747 is a great movement to work on and about as simple as they come.  It's the movement that I would recommend a new hobbyist try to tackle first.  The bridges only have two axles to line up and the axles are short so they're easy to get into place.

 photo Vardon06_zpsc9445c89.jpg

I happened to have a crystal and gasket set for the Vardon.

 photo Vardon02_zps923e3dfb.jpg

As you can see below, the original Vardon crystal is slightly more domed than the crystal that is currently on the watch.  Unfortunately the Vardon crystal has yellowed with age so I'll keep the flat crystal that is on the watch - it's more colorless.

 photo Vardon03_zps3355f76c.jpg

Once the movement is taken apart, the mainspring barrel can be opened up to access the mainspring.  As you can see below, it's broken a little more than half way through the coil.  The friction between the coils was enough to allow some tension to be applied and run the watch.  However, since it's not held firmly the spring would slip when too much tension was created - thus never getting fully wound.

 photo Vardon07_zps00ba98b1.jpg

With the arbor and center of the mainspring removed you can clearly see where the break was.

 photo Vardon08_zpsfbacefef.jpg

All the parts (except the balance and pallet fork) go into the cleaning solution.  The balance and pallet fork get cleaned separately in order to protect the jewels that are held in place with shellac.  I'm not worried about the solution, it's the ultrasonic that will shake them loose if I'm not careful.  The ultrasonic with also move the timing screws in the balance wheel - and mess up the poising of the balance.

 photo Vardon09_zps65ac95dc.jpg

Everything goes back together nicely and the watch goes onto the timer.  You can see the effect of tweaking the regulator starting under the number 252… the rate went a little faster, then it evened out a little toward the right side under the 18000.  The results leave the right side of the screen and then come back on the left side, overwriting the prior results.  So by the time it reached the 252 again it was running about 12 seconds fast per day.  Not bad for a 60+ year old watch.

 photo Vardon10_zpsbdae08c0.jpg

I had one small casualty while reinstalling the dial and hands… a small section of the lume on the hour hand disintegrated when I pushed the hand back on the hour wheel.  Putting new lume on it would look silly so I just applied a little model paint that was a fairly close match.  Someday when the dial and hands get redone they will all match each other again.  Until then, this will have to do.

 photo Vardon11_zps12e16356.jpg

This style of hands is called "hollow leaf" and when set to the traditional Hamilton time of 10:12 they remind me of the Cheshire Cat peering back at you like in Alice in Wonderland.

 photo Vardon12_zps83dfa9f7.jpg

Other than the unfortunate hour hand issue, this Vardon turned out great, I think.  It's definitely a fine example of the model - that's for sure.

Monday, January 20, 2014

Tools you need...

I started this blog a couple of years ago as an outlet for what has become a very passionate hobby.  For me, it is just that - a hobby.  It's intensely rewarding to restore a watch to good timekeeping.  It also can be extremely frustrating and unforgiving.  It's sort of like golf - except I can do it in an hour and at night.

Like pretty much everyone, my interest in watches was piqued by inheriting some family pieces.  Some, like the Hamiltons, I was able to get repaired and working as they should.  There were others that I could not get repaired because watchmakers didn't want to work on the more garden variety makes (like a 7 jewel New York Standard).   I realized that if I was going to get my great grandfather's New York Standard working, I would have to do it myself.

So I did.

One of the barriers to collecting is the maintenance costs.  Every "new" vintage watch should be serviced before wearing, unless you buy it as serviced from someone you trust.  Overhauls can easily add another $75 - $100 to each new acquisition and that can really add up fast.

One of the fringe benefits of restoring Hamiltons is I have met a lot of very nice people along the way.   I get asked frequently by new collectors about how to get started in doing their own work.  This is not an easy "row to hoe", as they say, but with patience and dedication it can be learned.

If you wanted to give it a try, here are the basic tools that you will need.  As a general rule, buy quality tools.  They are worth the slightly higher investment.

First, you need to be able to see what you are doing.  If your eyesight is perfect you might be able to get by with just an occasional loupe.  For me, I like to wear a jeweler's visor with a flip down monocle for additional magnification when needed.  An additional 10X loupe is helpful for checking jewels for dirt or cracks.

 photo Tools15_zps37412d1b.jpg  photo Tools13_zps1a6c8f87.jpg

Next, you're going to need to get into the watch.  That can usually be done with either a case knife, a case wrench or a crystal lifter.

 photo Tools07_zps42060db0.jpg

 photo Tools05_zpsb87c23bd.jpg

 photo Tools16_zpsc3672956.jpg

Now that you have access to the movement - the next tool you will need is a screwdriver.  Screwdrivers come in various widths.  You should always match the width of the screwdriver to the width of the screw head.  Fortunately you can purchase sets of the most common sizes.  If you want to do pocket watches too - you'll want a 7 or more screwdriver set.

 photo Tools03_zps411a9b95.jpg

At this point you have all the tools necessary for getting to the dial-side of the movement.  You'll want to pull the hands and dial so in addition to a screwdriver (for the dial foot screws) you'll need a hand puller.  I like the Presto style.

 photo Tools06_zps97ccff65.jpg

At this point you'll need to have a movement holder.  You do not want to attempt this type of work without a quality holder.  I like the Bergeon 4040, myself.  There's a smaller version (4039) for smaller watch movements like ladies grades.  They're reversible too - so you can do up to size 16 size pocket watches in the 4040.

 photo Tools08_zpsf422e4bf.jpg

With the movement secured in a holder, you're going to need tweezers to grasp small parts as you remove them.  My usual go-to tweezers are Dumont 3C but you'll want some heavier tweezers too.  Fine tweezers are very important and you want them to be strong so you don't have to constantly dress them.  Plus, you want a gentle touch - as the slightest pressure will send small parts flying, never to be seen again.  (Did I mention this is a frustrating hobby?)

 photo Tools09_zps6b0b28b9.jpg

At this point you have all the tools needed to completely disassemble a watch and to reassemble it once the parts have been cleaned.  Cleaning the parts can be done in an ultrasonic jewelry cleaner of your choosing.  The solutions you clean with is important too.  There are lots of tricks of the trade but commercially available cleaners and rinses work best, in my opinion.  I use L&R ultrasonic non-ammoniated watch cleaner and rinse.  I also use "one-dip" for hairsprings and pallet forks.

I have three baby food jars, one for cleaner and two for rinse.  The parts go into the cleaner, then the first rinse jar and then the second rinse jar.  Each jar goes into a water-bath in the ultrasonic for about 7 minutes.  So it takes a good 20+ minutes to clean all the parts.  Hairsprings and pallet forks don't go into the ultrasonic - you don't want to shake loose the jewels that are held in place with shellac.

Depending on what else you have to do - you might need a mainspring winder to install a fresh mainspring in the barrel.  It's possible to do it by hand but it's very challenging.  A winder makes easy work of it.  I like K&D style winders, myself.  They come in different sizes and are adjustable for different size barrels.

 photo Tools02_zpseecd1ea3.jpg

When you reassemble a watch, every jewel needs to be properly oiled.  I use three types of lubricants in each watch I service.  I use Moebius synthetic 9010 watch oil in all the jewels, Moebius 8200 mainspring grease, and finally I use KT-22 lubricant on the stem and keyless works.  Modern watches could use other lubricants too - but since all the movements I work on predate modern lubricants, I just go with the basics.

You'll need an oiler to apply a tiny droplet of oil to each jewel.  Oilers come in different sizes and look like tiny spoons.  Blue is what I typically use.  Black is even finer and I use that on ladies watches.

 photo Tools10_zps3d59786a.jpg

Changing out stems is best done with a pin vise.  They allow you to grab the stem and screw it into, or out of, the crown.  You can also use some flat jawed pliers.

 photo Tools11_zps454ce7b2.jpg

 photo Tools12_zpsed14e0c1.jpg

By now you've got all the basic tools needed to overhaul a watch.  If the watch has a problem, then you might be outgunned.  Things like "polishing pivots" and hairspring work require skills beyond the basic hobbyist.

Assuming the watch is running once you're finished with it, you'll want to make sure the watch keeps accurate time.  There's really only one way to do that - and that's to use a watch timer.  They're pretty expensive but basic ones can be had for a couple hundred bucks.  You can try using the stop watch on your phone - but truly accurate measurement requires a timer.

With the watch regulated, you still have to put the dial and hands back.  The dial just slips right over the cannon pinion and hour wheel.  You tighten the dial foot screws and then place the hour hand on the hour wheel with tweezers.  The minute hand goes on top and you can press the minute hand down with a hand pusher.

 photo Tools14_zps7857f954.jpg

You might be able to get by with a flat No.2 pencil eraser.

Everything goes back in the case and the case gets properly buttoned up.   All you need now is to put on a new strap.  You'll want a quality spring bar tool for this finishing touch.  A fine spring bar tool is immensely helpful when there isn't a lot of clearance.

 photo Tools04_zps46b72a5f.jpg

Of course, the first few times you do this I can pretty much guarantee that you're going to break something like a balance staff, or an escape wheel pivot.  It's best to practice with one movement, over and over, until you know exactly where everything goes and how to install it.   Parts movements will eventually equip you with the spare parts you need to replace the things you break or lose.

Eventually you'll have so many broken balances laying around that you'll be tempted to learn how to replace them.  That's going to require a staking set.  In fact, a lot of basic operations require staking tools to various ilk.  For example, hands can be tightened or loosened using a staking set.  Cannon pinions can be tightened on a staking set.  Jewels can be removed and replaced with staking tools.

 photo Tools01_zpse7319cf8.jpg

After reading all of the above - if you're still crazy enough to want to get into this hobby then you should start with this basic investment and refer to it a LOT.  The Watch Repairers Manual was written a long time ago but since these watches were made back then, you'll find the book to be a great reference.  Don't be surprised if you are overwhelmed by the complexity of some things.  Once you develop some confidence you can take more in.

 photo Tools17_zps5ff981e2.jpg

One of the most important things to understand is that there are a lot of very talented professional watchmakers out there.  They've gone to trade schools, studied under other master watchmakers, and have expensive equipment to tackle the most challenging of tasks.  It's a good idea to seek out the watchmakers in your area and develop a rapport with them.  They're professionals and skilled at their craft.  Therefore, most will not be interested in fixing projects that you have screwed up.  However if you respect that this is how they make their living (and it's not easy work), they will hopefully encourage your continued development.

Checkout the AWCI website to find the watchmakers nearest you.   The American Watchmakers-Clockmakers Institute

Sunday, January 19, 2014

1935 Turner

It's funny how some watches are abundantly found and some are very hard to come by.  Obviously popularity at the time of release and the number of years a watch was produced are major factors.   And, of course, there are a number of situations where very few examples were made to begin with.   I think another important factor is the quality of the case - I bet a lot of nice watches have been lost to time by wearing out the case.

Take for example the 1935 Turner.  It was produced for two years.  There were over 6,100 yellow gold  filled models and only 420 white examples, according to Rene Rondeau's great reference book.  I can understand not seeing any white Turners - but yellow ones are pretty darned scarce too.

 photo ScreenShot2014-01-19at43735PM_zps56136e50.png

The Turner came in a 10K gold filled case - and one of the interesting things about the case is it doesn't say Hamilton inside it.  It's made by Keystone and is marked 10K gold filled.  If you didn't know better,  you might suspect that it's a jobber case but it's not.

Turners are notoriously prone to wear through on the high points - so I think that's one reason they are hard to come by - I bet a lot of cases were worn through and discarded.

Being produced in 1935 and 1936, you're just as likely to find a 17 jewel 987F as you are to find a 987E under the dial.

Three dials were available… an applied gold marker dial, a black enamel numeral dial (1936), and a combination black marker / numeral dial (1935).  The latter is especially interesting since it's quite unusual.

I've been on the prowl for a Turner for ever, basically.  Having a 6/0 sized movement, it's actually a nice sized watch, even by today's standards.  As fate would have it, I purchased a project watch example that was for sale from another collector.  In fact, check out his vintage watches for sale on his site… waterstonewatches.com

As received, the watch had the usual dirt and grime one expects to see on an 80 year old watch.  The crystal was plenty scratched, but the bezel was largely wear-free.

 photo Turner01_zps78bc8721.jpg

The case back has some wear to the opening lip and a minor dent on the left side but is otherwise tight. The bezel and the back needed a little tweaking to get the two to close tightly but I was able to correct that without much difficulty.

 photo Turner02_zps19d7c32a.jpg

Here's the inside of the case back… no "Hamilton Watch Company" in here.  Most jobber cases have rolled gold plate or even stainless steel case backs - so that's another good sign the case is correct for a Turner.

 photo Turner03_zpsa4f6cd85.jpg

Here's the 17 jewel 987F.  The serial number dates it to 1935, just as it should.  It's pretty dirty but it runs - so that's a good sign that just an overhaul will be needed to restore it to good health.

 photo Turner04_zps683bc9b5.jpg

The usual thorough-cleaning and a fresh white alloy mainspring result in vigorous amplitude and almost spot-on time keeping right out of the chute.  No tweaking needed for this watch.

 photo Turner05_zps4985d5b1.jpg

And here is it all spiffed up with a fresh glass crystal and new brown lizard strap.  This style of hands is called "baton" and are the correct style for Turners.  My camera always surprises me by pointing out every flaw but other than a little wear to the lower right lug, this bezel looks fantastic!

 photo Turner07_zpsbf3351ea.jpg

 photo Turner06_zpsda0ccc10.jpg

And here's an example of the 1935 black combination marker / numeral dial, courtesy of fellow collector Bryan Girouard.  Bryan offers a lot of fantastic vintage watches for sale - check out his site and buy with confidence… artdecowristwatches.com

 photo ScreenShot2014-01-19at52616PM_zpsdd0f702c.png