Pages

Saturday, April 6, 2019

WWII US Navy Model 27023

Arguably the rarest Hamilton WWII models are the watches made for the US Navy and Marine Corps.  110,000+ white-dialed models were made for the US Army and marked ORD-DEPT while it's not entirely clear how many black-dialed models for the US Navy were made.  There are records for the 987S and 2987 sweep second models for naval aviators but the other USN models with 987A are much less common.

I've posted about WWII models before but I recently had the opportunity to work on a 27023 model and thought I'd show you it's details.  Hamilton's WWII models with 987A movements supposedly had minor alterations to meet military specifications, including a new balance staff design.

My project watch came from a fellow collector and he sent it to me after a slight mishap.  Can you guess what happened?  If you guessed face-plant, then you're right.  He dropped it on a hard surface and it broke the crystal.  Whoops!


This watch has a really cool period correct sterling silver bracelet.


The other side has a medallion from Pearl Harbor Naval Shipyard.  This public shipyard is still in operation today.  Notice the H on the case between the lugs - that's one of the clues to look for to determine authenticity.  This model has a Keystone case and it should have an H between the lugs.


If you look really closely you might be able to see this watch somewhere in the photo below... it was there at the same time.


The back of the case is properly marked with R88-W-800 and the part number 27023.


Inside the case back is a unique serial number for the watch.


The movement is held within a movement ring and a dust cover snaps onto the ring.  A gasket surrounds the cover and seals the case back when it's screwed on.


The movement number starts with an O (oh) and dates the watch to 1944.


Models for the US Navy have black dials with luminous numbers and hands.  The hands should be stainless steel and these are the correct hands.


This watch already has a white alloy mainspring installed so I will reuse it.


Everything is cleaned, dried, and ready for reassembly.


The reassembled movement is ticking away with a good motion.  Let's see what the timer thinks of it.


Not too shabby.  The beat error of 2.7ms is on the higher end of my acceptable specs and the amplitude is a vigorous 316 degrees.  Should I try to reduce the beat error?


Well, the most desirable amplitude is between 250 and 300.  If amplitude gets too high the balance can swing all the way around and hit the opposite side of the pallet fork, causing it to bounce back and make the timing go wonky.  Amplitude will be higher when the movement is dial up or dial down since the friction is lowest in those positions.  When the movement is on edge all of the pivots are in use so the amplitude drops slightly.  If I decrease the beat error, the amplitude will increase.  So, since the amplitude is already pretty high, I think I'll leave the beat error as is.  The watch will stop a little sooner than if the beat error were lower but not that much sooner.

A new crystal definitely goes a long way toward making this watch look a lot better.  Now my friend just needs to make sure he doesn't drop it again!


5 comments:

  1. I have one of these watches that was issued to my father-in-law when he was in the Marines. I've had it serviced and it is now working properly. It is in overall good to very good condition. He might have replaced original band with a leather one because he wore this watch while he worked on the far. How much is a watch worth? - Dave

    ReplyDelete
    Replies
    1. Being a family piece I’d say it’s priceless but to purchase a similar watch would probably be $600-$800

      Delete
    2. Dan, thanks for your reply. Do you work on other brands of watches like Waltham , Buren or others? We just re-discovered a Waltham pocket watch model 1908 17 jewel 16s circa 1908 according to the serial number. The case appears to be gold filled and has front and back cover Hunter design? It appears to be in very good, working condition.

      Delete
  2. Hi man. Do you know where I can get a replacement crown for one of these? I see a listing for a bulova 10bnch that's tap 10. Its turned to brass maybe I should just leave it though.

    ReplyDelete